Difference between revisions of "Junctionary - Logic and Other"
From #openttdcoop wiki
| Line 10: | Line 10: | ||
| − | {{Junctionary|11.01.11|[[Image:psg131_Compressor.png|center|140px|]]|''Train packing'''|The so called compressor. Waits until a few trains are ready to go and then releases them very close together, allowing trains further down the line join. |{{User|Mark}}|{{PublicServerGameSave|131}} }} | + | {{Junctionary|11.01.11|[[Image:psg131_Compressor.png|center|140px|]]|'''Train packing'''|The so called compressor. Waits until a few trains are ready to go and then releases them very close together, allowing trains further down the line join. |{{User|Mark}}|{{PublicServerGameSave|131}} }} |
{{Junctionary|11.01.11|[[Image:psg180_flipflop.png|center|140px|]]|'''Flipflop'''|A typical flipflop splitting trains into 6 directions equally. |{{User|V453000}}|{{PublicServerGameSave|180}} }} | {{Junctionary|11.01.11|[[Image:psg180_flipflop.png|center|140px|]]|'''Flipflop'''|A typical flipflop splitting trains into 6 directions equally. |{{User|V453000}}|{{PublicServerGameSave|180}} }} | ||
Revision as of 10:07, 29 September 2011
| Logic and Other | |
|---|---|
|
Back to junctionary |
It is hard to describe logic shortly since it's very purpose is to do something extra. In this section can be found mechanisms and thingies that usually control trains somehow, and thus improve how our network works. Although there are for sure even cases that are completely useless like train counters.
| Logic and other constructions (what is that?) | ||||||
|---|---|---|---|---|---|---|
| Date | Screenshot | Specification | Description | Creator | additional
| |
| 13/07/2008 |  |
Train Length Sorter | Sorts trains by their length. In this example trains longer than 5 cars (or 2 tiles) will be sorted via the penalty, those of 5 cars or less through the non-penalty line. this is useful when trains of varying type use a station, and some platforms are shorter than others. It can also be used at junctions where there are two options of track, to move shorter trains onto a loop with tighter turns. Finally it may be used to seperate main line trains from local trains (assuming different train lengths). A local train may be forced onto a longer, slower loop to allow mainline trains to pass. | Audigex, original credit unknown. |
| |
| 16/12/2008 |  |
Advanced Timer | An advanced timer which works with a certain cycle. Once the dummy train finishes the cycle, a train is released by the timer. However this has one crucial condition - if a train overflows, the whole cycle is cancelled and the counting starts again. | Mark | Download PSG #121
| |
| 11.01.11 |  |
Train packing | The so called compressor. Waits until a few trains are ready to go and then releases them very close together, allowing trains further down the line join. | Mark | Download PSG #131
| |
| 11.01.11 |  |
Flipflop | A typical flipflop splitting trains into 6 directions equally. | V453000 | Download PSG #180
| |
| 11.01.11 |  |
Counter | A mechanism which counts how many trains have passed a certain spot. Completely useless for the network. | HDIEagle | Download PSG #196
| |
| 11.01.11 |  |
Counter/comparer | This array of stations had a special overflow which counted which station gets the least amount of trains and released trains to that. Therefore there are logic mechanisms which count how many trains have passed (based on Mark's clock) and a mechanism which says which station had gotten X trains as the last one. | V453000 | Download PSG #200
| |
| 11.01.11 |  |
Long train abuse | This mechanism is meant to pack looong trains in just 3x3. It is very slow due to the effective more than 1xTL signal gap. | V453000 | Download PSG #203
| |
